Information

Manuel

DALI Jalousie DIN Rail Module

The DALI Jalousie DIN Rail module is designed for controlling 230V blind motors via DALI. This module supports four functions for opening and closing the blinds and adjusting the slat angle.

Product Types

• Art. Nr.: 86458676-HS DALI Jalousie DIN Rail
• Art. Nr.: 86458676-DE DALI Jalousie Ceiling Mount

Interface Overview

• Suitable for controlling blind motors with separate 230V inputs for up and down via DALI
• Outputs are interlocked
• Suitable for load currents up to 4A
• Control via DALI commands: RECALL MAX or UP for up, RECALL MIN or DOWN for down, OFF to stop
• Power supply via DALI line, no additional supply required
• One DALI address and four programmable functions for adjusting the slat angle and opening/closing the blinds

Specifications

Electrical Data

• Power supply: from DALI bus
• Typical DALI current consumption: 5.5 mA
• Input (Voltage and Frequency): 120/240VAC 50/60Hz
• Output: 120/240V (up/down, interlocked)
• Relay contact switching voltage: 250Vac
• Maximum nominal load and current: 1000VA / 4A
• Switching cycles at 8A/250Vac, resistive: 10⁵
• Max. relay switching frequency: 0.2 Hz

General Data

• Mounting: DIN rail, ceiling mount
• Dimensions (LxWxH): 98mm x 17.5mm x 56mm (DIN rail), 120mm x 30mm x 22mm (ceiling mount)
• Maximum operating temperature: 75°C
• Protection class: II with proper mounting
• Enclosure protection rating: IP40
• Terminal protection rating: IP20

Environmental Conditions

• Transport and storage temperature: -20°C to +75°C
• Operating temperature: -20°C to +60°C
• Relative humidity, non-condensing: 15% to 90%

Terminals

• Connection type: Screw terminal, spring terminal
• Wire capacity single core: 0.5 to 2.5 mm² (AWG20 to AWG14), 0.5 to 1.5 mm² (AWG20 to AWG16)
• Wire capacity stranded: 0.5 to 2.5 mm² (AWG20 to AWG14), 0.5 to 1.5 mm² (AWG20 to AWG16)
• Wire capacity with ferrules: 0.25 to 1.5 mm², 0.25 to 1 mm²
• Strip length: 7 mm / 0.27 inch, 8.5 to 9.5 mm / 0.33 to 0.37 inch

Standards

• DALI EN 62386-101
• EMC EN 61547, EN 55015 / IEC CISPR15
• Electrical safety EN 61347-2-11, EN 61347-1
• Certifications: CE, UKCA

Function

The DALI Jalousie module can be controlled via the assigned DALI address. It converts DALI commands into up/down control commands for the blind motor control. The 230V motor control signals (for up and down) are interlocked, only one signal is issued to the motor control at a time.

Module Behavior on DALI Commands

• DALI command: RECALL MAX / UP – Blind motor: Up – Signal: 230V
• DALI command: RECALL MIN / DOWN – Blind motor: Down – Signal: 230V
• DALI command: OFF – Blind motor: Stop – Signal: 0V

Profiles and Scenes

There are four freely adjustable profiles available to adapt the module to the specific blind. These profiles can be used to call up custom drive profiles (direction and duration) using scene commands.

Technical Data

• Operating temperature: -20°C to +60°C
• Protection rating: IP20
• Wire capacity: DIN rail: max. 2.5mm², ceiling mount: max. 1.5mm²

The DALI Jalousie DIN Rail module is available in gray.